Why Does My Rolls Royce Phantom Key Fob Not Work?
The Rolls-Royce Phantom is a luxury car that reflects the utmost in luxury and class. Its large waterfall-style grille and traditional upright dimensions are immediately recognizable. It is also one of the world's most expensive cars.
The key fob for the rolls royce could stop working due to various reasons. A dead coin battery is the most common cause, but other reasons include water damage or receiver modules.
Battery
The most common reason for a Rolls-Royce Phantom key fob not working is the dead coin battery within. It is important to remember that the key fob could also stop working due to other causes, like damaged buttons or water damage. Other reasons include signal interference, bad battery contacts, or keys that aren't paired which require reprogramming. If your key fob stops functioning, you may want to consult with locksmith. A locksmith can identify the problem quickly and provide an immediate solution.
To ensure that the battery is fully functional, it must be protected from moisture and dirt. This is the reason why it is recommended to always use a case for your key fob that is waterproof when you travel. It is also recommended to remove the battery from the key fob before cleaning or washing it. The key fob's chip is sensitive to water and should not be left exposed to soapy or salty water. If the key fob is likely to be exposed to water, you can use electronic cleaner or isopropyl to prevent damage.
The battery pack of the Phantom EE has a variety of innovative features that distinguish it from the traditional power systems found in other luxury cars. For instance there is the "power reserve dial" has been added to the dashboard that communicates the status of the car's energy supply to the driver. This is a new design feature that is designed to challenge conventional car-related paradigms and showcase the potential of alternative drive-train technology.
One of the main advantages of this electric powertrain is that it allows charging to be re-charged without the need for a physical connection between the car and its charging station. This is accomplished by using induction. The Key Lab is the transfer of power between two surfaces that include an induction mat on the ground, and a power-transfer unit under the battery pack.
Recharging takes place in two phases, and has a the capacity to charge total of 71kWh. Each phase is able to hold 13.5kW. It is the biggest battery for a car's engine in the world. The Phantom EE also comes with three different chargers that can be used for both single-phase or 3-phase charging and also Regenerative braking.
Contacts
If your Rolls Royce Phantom remote key fob isn't functioning, the problem could be due to an inactive battery or worn buttons. Fortunately, this issue is usually fixable. You could also try reprogramming the key fob or replacing the battery with 12 volts. If the problem persists the receiver module might be faulty. The receiver module is used by the remote keyless system to communicate with other onboard electronics through radio signals. If the receiver module is defective, it will cease to communicate with the key fob or other electronic components onboard.
If you're having problems with your key fob make sure that the battery contacts are clean and dry. The metal clips that hold the button cell battery in place and complete the circuit can be damaged by moist or dirty hands. If the battery is old, you should replace it with a new one that has the same voltage and size. If you replace the battery, make sure to clean the contact surfaces with rubbing alcohol or electronic cleaner prior to making the key fob.
The key fob on the Rolls Royce Phantom is equipped with an electronic chip that sends signals to the remote keyless system receiver module. The module then converts the signals into commands the car can comprehend and respond to. This is how your car can tell that you're looking to unlock the doors or retract the famous "flying lady" ornament on the hood into the grille.
If the key fob was exposed to water, immediately remove it from the vehicle and wash the electronic chip using isopropyl alcohol, or electronic cleaner. If you do not then, the chip could be damaged.
Water damage
The key fob is designed with rubber seals that prevent the chip inside from being exposed to water. This makes it resistant to light rain and splashes but not the kind of deep immersion that might be experienced when you drop your key into a puddle or submerge it in the ocean. If the fob is wet the chip could be damaged. It is necessary to replace it.
Even if you've not dropped your key fob into the water, but it's affected by a wet dog washing machine, or soapy handwashing, don't worry because your roll royce phantom key fob could be salvageable. All you have to do is follow a few simple steps and you'll be able to save yourself the expense of purchasing the new key.
The first step is to take the key fob apart and dry it completely. Take the battery off when you can, and use compressed air to blow any excess moisture from the key fob. After you've done this, leave it to dry out for a few days and try it again.
If your key fob is susceptible to soaking by moisture it's a good idea to purchase a waterproof case which can protect it against accidents. It is also advisable to keep a spare fob in hand to avoid waiting for it to dry.
Your Rolls Royce Phantom remote key may stop working in some cases due to interference, or the battery is dead. This problem is often caused by objects, adverse weather conditions or transmitters operating at the same frequency as your remote.
Keep your key fob far away from these sources. If you cannot get rid of these sources of interference, you can move your car to a different location or reprogram the remote. If you're not able to resolve the issue, you should to speak with a professional technician. They will be able to identify the issue and determine if it's mechanical or electrical fault.
Reprogramming
The key fob inside your Rolls Royce Phantom is an important component of your vehicle's security system. It transmits commands from the key fob to the receiver module, which then sends the commands to the central locking mechanism of the vehicle. It can be frustrating and costly if the key fob fails to function. There are a few easy methods you can use to get your key fob to work again.
Examine if the battery in the key fob has failed. It is a common cause of Phantom key fob not locking or unlocking issues and usually signs of deterioration such as an insufficient range. Replace the battery with a fresh one of the same voltage, size, and specification. Make sure that the clips that keep the batteries in place aren't loose.
Another possibility is water damage. The key fob has rubber seals that block water from reaching the electronic chip inside. However, if it gets soaked in salty or soapy water, the seals may break down. If this happens, take the battery from the fob and clean it using isopropyl or electronic cleaner. After drying then put it back in the fob.
If the key fob still isn't working it could be a sign the receiver module has been faulty. The best way to identify this is to connect an electronic diagnostic scanner to the OBD port located under the dashboard of your Phantom. The scanner will then ask to provide certain details regarding your car, such as the year model, year, and type. You will also be asked to enter the number from your key fob.
Signal interference is a second possible cause. This can be caused by weather conditions, objects or transmitters operating on the same frequency as your key fob. The remote control will work when you're close to the Phantom but it won't lock or unlock from a distance. This can be resolved by removing objects that may block the signal, or by moving the Phantom further away from the transmitters.